Home / News / Pepin introduces discontinuous unidirectional DiscoTape

Pepin introduces discontinuous unidirectional DiscoTape

26 Apr '12

5 min read

Pepin Associates Inc has developed a discontinuous, unidirectional preimpregnated reinforcement tape (unitape) which has the ability to stretch up to 30% to form complex shapes.

The material, called DiscoTape (subject of provisional patent), has shown promise in the formation of composite parts with complex curvatures normally precluding the use of unitape without cutting and darting. The material can be made with glass or carbon fiber prepregged with epoxy resins or thermoplastics. Variations of fiber lengths and segmentation patterns have been investigated to optimize DiscoTape for a variety of applications.

Two project engineers at Pepin Associates have conducted research on DiscoTape to ascertain its mechanical properties as compared to continuous tape, determine its forming limits and evaluate its use for composite structures such as keels, frames, fairings and radomes.

Mechanical testing conducted by Project Engineer Amber Simmons shows that while there is a knockdown of 0° tensile strength in the discontinuous unitape, interlaminar shear and in-plane shear remain relatively consistent with those properties of continuous unitape.

Tensile modulus is also close to continuous reinforcement values. This would allow use of DiscoTape in structures whose designs are stiffness driven such as bead stiffened shear panels. The ability of the discontinuous unitape to stretch and form complex parts, such as the hemisphere featured in Photo No 1, could enable manufacturers to use unitape where it hasn't been used in the past.

One possible application for DiscoTape is radomes. These fiber-reinforced composite structures are used to protect radar equipment on aircraft and rotorcraft during flight. The extreme environments these structures must endure during all aspects of flight, especially for military platforms, require strength and durability. However, these same structures must be as close to transparent as possible in allowing radar frequencies to penetrate the structure.

Pepin Associates Project Engineer Elizabeth Thompson has completed a study on the formability and transmissivity of glass DiscoTape, applicable for use in radome manufacture. Elizabeth formed test specimens of discontinuous glass prepreg unitape (DiscoTape) and Pepin Associates contracted with Radant Technologies of Stow, Massachusetts to measure the electrical properties of these specimens.

Pepin Associates, Inc. has shown that discontinuity does not always affect transmissivity of the radar signal. It was found that the discontinuity may interfere with the signal at X-band frequencies. In the event the material is showing signal loss, the length of DiscoTape segments can be altered easily, allowing the fabricator to 'tune' the material as needed. The research showed no appreciable effect on the material transparency for the Q-band frequency. Elizabeth Thompson details these conclusions in her technical paper, which will be presented at the 2012 SAMPE Conference in Baltimore, MD.

These results are promising because radome shapes are as variable as the aircraft on which they are mounted. Aircraft and rotorcraft radomes all have a cone or hemispherical component which is a challenge to fabricate with fiber-reinforced composite materials. Forming such complex curvatures with continuous, unidirectional tape is a challenge due to wrinkling of the material. Wrinkles can degrade both the radar signal and radome structural integrity. Applying unidirectional reinforcement tape to fabricate these parts without wrinkles is difficult and time consuming: DiscoTape could allow the formation of these shapes without wrinkling.

DiscoTape has the potential to be used on many other structures ranging from wind blades to medical imaging equipment to structures for aircraft and rotorcraft. Pepin Associates is seeking to evaluate DiscoTape applications for hard-to-form parts and structures commonly made with continuous unitape. The part shown in Photo No 2 is the secondary structure of a modern military jet, formed with carbon fiber DiscoTape.

“We believe the forming capabilities of DiscoTape will provide a significant manufacturing advantage in terms of time savings and reduction of scrap material versus the use of continuous unitape”, said John Pepin, President of Pepin Associates. “There is more development work to be done, but our initial resullts are very promising”, Pepin added.

Construction Textiles

Leave your Comments

RECOMMENDED

EU launches strategy for leadership in advanced materials sector
Construction Textiles

STFI to showcase lightweight construction innovations at JEC World
Construction Textiles

Ahlstrom completes major investment at Madisonville plant in US
Construction Textiles

Rivertex Australia managing director Gavin Hodgins. Pic: Rivertex

Newly established Rivertex Australia gets Gavin Hodgins as MD
Construction Textiles

Europe’s Ahlstrom launches new FibRoc solution for plasterboard market
Construction Textiles

US’ Owens Corning’s sales rise 16% to $2.6 bn in Q2 FY22
Construction Textiles

WSU researchers use disposable masks to make durable concrete
Construction Textiles

Scott Bader expands Crestabond structural adhesives to North America
Construction Textiles

Pepin introduces discontinuous unidirectional DiscoTape

Leave your Comments

Weekly technical textiles newsletter

ABOUT TECHNICAL TEXTILES

Main LINKS

Quick Links

Follow us